Difference between revisions of "BIOMETRICS INSTALLING AND SETTINGS"
From SPGC Document Wiki
| Line 17: | Line 17: | ||
<center>''Figure 2.0''</center> | <center>''Figure 2.0''</center> | ||
| − | 1. Install SDK – This module will install SDK or the Software Development Kit. | + | 1. '''Install SDK''' – This module will install SDK or the Software Development Kit. |
| − | 2. Remove SDK – This module removes the Software Development Kit. | + | 2. '''Remove SDK''' – This module removes the Software Development Kit. |
| − | 3. Reinstall SDK – This module will reinstall the SDK. | + | 3. '''Reinstall SDK''' – This module will reinstall the SDK. |
*This dialog box will appear after clicking ''“Install SDK”''. Click ''“Yes”'' to install and ''“Cancel”'' to abort installing SDK. | *This dialog box will appear after clicking ''“Install SDK”''. Click ''“Yes”'' to install and ''“Cancel”'' to abort installing SDK. | ||
| Line 51: | Line 51: | ||
<center>''Figure 4.0''</center> | <center>''Figure 4.0''</center> | ||
| − | 1. Install BMT Service - This module should be install before running BMT Service. | + | 1. '''Install BMT Service''' - This module should be install before running BMT Service. |
| − | 2. Remove BMT Service – This module removes BMT Service. | + | 2. '''Remove BMT Service''' – This module removes BMT Service. |
| − | 3. Reinstall BMT Service – This module will reinstall the BMT Service. | + | 3. '''Reinstall BMT Service''' – This module will reinstall the BMT Service. |
| Line 65: | Line 65: | ||
<center>''Figure 5.0''</center> | <center>''Figure 5.0''</center> | ||
| − | 1. Run BMT Service – This module runs the Biometric Management Tool. | + | 1. '''Run BMT Service''' – This module runs the Biometric Management Tool. |
| − | 2. Stop BMT Service – This module will stop the Biometric Management Tool. | + | 2. '''Stop BMT Service''' – This module will stop the Biometric Management Tool. |
| − | 3. Restart BMT Service – This module will restart the Biometric Management Tool. | + | 3. '''Restart BMT Service''' – This module will restart the Biometric Management Tool. |
Revision as of 10:55, 16 April 2019
Contents
I. Biometric Management Tool
*Biometric Management Tool has three steps to make the Biometric Management Tool Service run and it is installing sdk, installing BMT Service - Setting and BMT Service. ALWAYS REMEMBER before launching the system, you should always select RUN AS ADMINISTRATOR to run the system.
II. Installing SDK
- Click “Install SDK” to install.
1. Install SDK – This module will install SDK or the Software Development Kit. 2. Remove SDK – This module removes the Software Development Kit. 3. Reinstall SDK – This module will reinstall the SDK.
- This dialog box will appear after clicking “Install SDK”. Click “Yes” to install and “Cancel” to abort installing SDK.
- After Clicking “Yes” button, the command prompt will pop up and it will notify that installation is successful.
III. Installing BMT Service – Setting
- Click “Install BMT Service” – Setting to install.
IV. Installing BMT Service
- Click “Install BMT Service” to install and run BMT Service.
1. Install BMT Service - This module should be install before running BMT Service. 2. Remove BMT Service – This module removes BMT Service. 3. Reinstall BMT Service – This module will reinstall the BMT Service.
V. Running BMT Service
- Click “Run BMT Service” and the Biometric Management Tool will activated.
1. Run BMT Service – This module runs the Biometric Management Tool. 2. Stop BMT Service – This module will stop the Biometric Management Tool. 3. Restart BMT Service – This module will restart the Biometric Management Tool.
VI. BMT Service is Running
- If the steps in installing is done and you run the BMT Service, the system will indicate below that BMT Service is Running.
