Difference between revisions of "BIOMETRICS INSTALLING AND SETTINGS"
From SPGC Document Wiki
(→I. Biometric Management Tool) |
|||
| (8 intermediate revisions by the same user not shown) | |||
| Line 18: | Line 18: | ||
<center>[[File:sdk.JPG]]</center> | <center>[[File:sdk.JPG]]</center> | ||
<center>''Figure 2.0''</center> | <center>''Figure 2.0''</center> | ||
| + | |||
| + | |||
1. '''Install SDK''' – This module will install SDK or the Software Development Kit. | 1. '''Install SDK''' – This module will install SDK or the Software Development Kit. | ||
| Line 24: | Line 26: | ||
*This dialog box will appear after clicking ''“Install SDK”''. Click ''“Yes”'' to install and ''“Cancel”'' to abort installing SDK. | *This dialog box will appear after clicking ''“Install SDK”''. Click ''“Yes”'' to install and ''“Cancel”'' to abort installing SDK. | ||
| + | |||
<center>[[File:install.JPG]]</center> | <center>[[File:install.JPG]]</center> | ||
| Line 30: | Line 33: | ||
*After Clicking ''“Yes”'' button, the command prompt will pop up and it will notify that installation is successful. | *After Clicking ''“Yes”'' button, the command prompt will pop up and it will notify that installation is successful. | ||
| + | |||
<center>[[File:sucesssdk.JPG]]</center> | <center>[[File:sucesssdk.JPG]]</center> | ||
<center>''Figure 2.2''</center> | <center>''Figure 2.2''</center> | ||
| − | |||
| − | |||
== '''III. Installing BMT Service – Setting''' == | == '''III. Installing BMT Service – Setting''' == | ||
| + | |||
*Click ''“Install BMT Service”'' – Setting to install. | *Click ''“Install BMT Service”'' – Setting to install. | ||
| + | |||
<center>[[File:installbmt.JPG]]</center> | <center>[[File:installbmt.JPG]]</center> | ||
<center>''Figure 3.0''</center> | <center>''Figure 3.0''</center> | ||
| + | == '''IV. Installing BMT Service''' == | ||
| − | |||
| − | |||
*Click ''“Install BMT Service”'' to install and run BMT Service. | *Click ''“Install BMT Service”'' to install and run BMT Service. | ||
| Line 52: | Line 55: | ||
<center>[[File:instalbmtservice.JPG]]</center> | <center>[[File:instalbmtservice.JPG]]</center> | ||
<center>''Figure 4.0''</center> | <center>''Figure 4.0''</center> | ||
| + | |||
| + | |||
1. '''Install BMT Service''' - This module should be install before running BMT Service. | 1. '''Install BMT Service''' - This module should be install before running BMT Service. | ||
2. '''Remove BMT Service''' – This module removes BMT Service. | 2. '''Remove BMT Service''' – This module removes BMT Service. | ||
3. '''Reinstall BMT Service''' – This module will reinstall the BMT Service. | 3. '''Reinstall BMT Service''' – This module will reinstall the BMT Service. | ||
| − | |||
| − | |||
== '''V. Running BMT Service''' == | == '''V. Running BMT Service''' == | ||
| − | *Click ''“Run BMT Service”'' and the Biometric Management Tool will activated. | + | *Click ''“Run BMT Service”'' and the Biometric Management Tool will be activated. |
<center>[[File:runbmt.JPG]]</center> | <center>[[File:runbmt.JPG]]</center> | ||
<center>''Figure 5.0''</center> | <center>''Figure 5.0''</center> | ||
| + | |||
| + | |||
1. '''Run BMT Service''' – This module runs the Biometric Management Tool. | 1. '''Run BMT Service''' – This module runs the Biometric Management Tool. | ||
2. '''Stop BMT Service''' – This module will stop the Biometric Management Tool. | 2. '''Stop BMT Service''' – This module will stop the Biometric Management Tool. | ||
3. '''Restart BMT Service''' – This module will restart the Biometric Management Tool. | 3. '''Restart BMT Service''' – This module will restart the Biometric Management Tool. | ||
| − | |||
| − | |||
== '''VI. BMT Service is Running''' == | == '''VI. BMT Service is Running''' == | ||
| Line 80: | Line 83: | ||
<center>''Figure 6.0''</center> | <center>''Figure 6.0''</center> | ||
| + | |||
| + | |||
| + | |||
| + | '''REFERENCE''' | ||
[[Media:Biometrics Installing.docx]] | [[Media:Biometrics Installing.docx]] | ||
Latest revision as of 09:27, 26 April 2019
Contents
I. Biometric Management Tool
*Biometric Management Tool has three steps to make the Biometric Management Tool Service run and it is installing sdk, installing BMT Service - Setting and BMT Service. ALWAYS REMEMBER before launching the system, you should always select RUN AS ADMINISTRATOR to run the system.
II. Installing SDK
- Click “Install SDK” to install.
1. Install SDK – This module will install SDK or the Software Development Kit. 2. Remove SDK – This module removes the Software Development Kit. 3. Reinstall SDK – This module will reinstall the SDK.
- This dialog box will appear after clicking “Install SDK”. Click “Yes” to install and “Cancel” to abort installing SDK.
- After Clicking “Yes” button, the command prompt will pop up and it will notify that installation is successful.
III. Installing BMT Service – Setting
- Click “Install BMT Service” – Setting to install.
IV. Installing BMT Service
- Click “Install BMT Service” to install and run BMT Service.
1. Install BMT Service - This module should be install before running BMT Service. 2. Remove BMT Service – This module removes BMT Service. 3. Reinstall BMT Service – This module will reinstall the BMT Service.
V. Running BMT Service
- Click “Run BMT Service” and the Biometric Management Tool will be activated.
1. Run BMT Service – This module runs the Biometric Management Tool. 2. Stop BMT Service – This module will stop the Biometric Management Tool. 3. Restart BMT Service – This module will restart the Biometric Management Tool.
VI. BMT Service is Running
- If the steps in installing is done and you run the BMT Service, the system will indicate below that BMT Service is Running.
REFERENCE
