Difference between revisions of "BIOMETRICS INSTALLING AND SETTINGS"

From SPGC Document Wiki
Jump to: navigation, search
(→‎I. Biometric Management Tool)
 
(17 intermediate revisions by the same user not shown)
Line 1: Line 1:
  
−
== I. Biometric Management Tool ==
+
== '''I. Biometric Management Tool''' ==
  
 
  *'''Biometric Management Tool''' has three steps to make the Biometric Management Tool Service run and it is installing sdk, installing BMT Service - Setting and BMT Service. '''''ALWAYS REMEMBER''''' before launching the system, you should always select '''''RUN AS ADMINISTRATOR''''' to run the system.
 
  *'''Biometric Management Tool''' has three steps to make the Biometric Management Tool Service run and it is installing sdk, installing BMT Service - Setting and BMT Service. '''''ALWAYS REMEMBER''''' before launching the system, you should always select '''''RUN AS ADMINISTRATOR''''' to run the system.
  
  
−
<center>[[File:home.JPG]]</center>
+
<center>[[File:runadmin.JPG]]</center>
 
<center>''Figure 1.0''</center>
 
<center>''Figure 1.0''</center>
 +
 +
 +
<center>[[File:home.JPG]]</center>
 +
<center>''Figure 1.1''</center>
 +
 +
== '''II. Installing SDK''' ==
 +
 +
*Click ''“Install SDK”'' to install.
 +
 +
<center>[[File:sdk.JPG]]</center>
 +
<center>''Figure 2.0''</center>
 +
 +
 +
 +
1. '''Install SDK''' – This module will install SDK or the Software Development Kit.
 +
2. '''Remove SDK''' – This module removes the Software Development Kit.
 +
3. '''Reinstall SDK''' – This module will reinstall the SDK.
 +
 +
*This dialog box will appear after clicking ''“Install SDK”''. Click ''“Yes”'' to install and ''“Cancel”'' to abort installing SDK.
 +
 +
 +
<center>[[File:install.JPG]]</center>
 +
<center>''Figure 2.1''</center>
 +
 +
 +
*After Clicking ''“Yes”'' button, the command prompt will pop up and it will notify that installation is successful.
 +
 +
 +
<center>[[File:sucesssdk.JPG]]</center>
 +
<center>''Figure 2.2''</center>
 +
 +
== '''III. Installing BMT Service – Setting''' ==
 +
 +
 +
 +
*Click ''“Install BMT Service”'' – Setting to install.
 +
 +
 +
<center>[[File:installbmt.JPG]]</center>
 +
<center>''Figure 3.0''</center>
 +
 +
== '''IV. Installing BMT Service''' ==
 +
 +
 +
*Click ''“Install BMT Service”'' to install and run BMT Service.
 +
 +
<center>[[File:instalbmtservice.JPG]]</center>
 +
<center>''Figure 4.0''</center>
 +
 +
 +
 +
1. '''Install BMT Service''' -  This module should be install before running BMT Service.
 +
2. '''Remove BMT Service''' – This module removes BMT Service.
 +
3. '''Reinstall BMT Service''' – This module will reinstall the BMT Service.
 +
 +
== '''V. Running BMT Service''' ==
 +
 +
 +
*Click ''“Run BMT Service”'' and the Biometric Management Tool will be activated.
 +
 +
<center>[[File:runbmt.JPG]]</center>
 +
<center>''Figure 5.0''</center>
 +
 +
 +
 +
1. '''Run BMT Service''' – This module runs the Biometric Management Tool.
 +
2. '''Stop BMT Service''' – This module will stop the Biometric Management Tool.
 +
3. '''Restart BMT Service''' – This module will restart the Biometric Management Tool.
 +
 +
== '''VI. BMT Service is Running''' ==
 +
 +
*If the steps in installing is done and you run the BMT Service, the system will indicate below that BMT Service is Running.
 +
 +
<center>[[File:runningbmt.JPG]]</center>
 +
<center>''Figure 6.0''</center>
 +
 +
 +
 +
 +
'''REFERENCE'''
 +
 +
[[Media:Biometrics Installing.docx]]

Latest revision as of 09:27, 26 April 2019

I. Biometric Management Tool

*Biometric Management Tool has three steps to make the Biometric Management Tool Service run and it is installing sdk, installing BMT Service - Setting and BMT Service. ALWAYS REMEMBER before launching the system, you should always select RUN AS ADMINISTRATOR to run the system.


Runadmin.JPG
Figure 1.0


Home.JPG
Figure 1.1

II. Installing SDK

  • Click “Install SDK” to install.
Sdk.JPG
Figure 2.0


1. Install SDK – This module will install SDK or the Software Development Kit.
2. Remove SDK – This module removes the Software Development Kit.
3. Reinstall SDK – This module will reinstall the SDK.
  • This dialog box will appear after clicking “Install SDK”. Click “Yes” to install and “Cancel” to abort installing SDK.


Install.JPG
Figure 2.1


  • After Clicking “Yes” button, the command prompt will pop up and it will notify that installation is successful.


Sucesssdk.JPG
Figure 2.2

III. Installing BMT Service – Setting

  • Click “Install BMT Service” – Setting to install.


Installbmt.JPG
Figure 3.0

IV. Installing BMT Service

  • Click “Install BMT Service” to install and run BMT Service.
Instalbmtservice.JPG
Figure 4.0


1. Install BMT Service -  This module should be install before running BMT Service.
2. Remove BMT Service – This module removes BMT Service.
3. Reinstall BMT Service – This module will reinstall the BMT Service.

V. Running BMT Service

  • Click “Run BMT Service” and the Biometric Management Tool will be activated.
Runbmt.JPG
Figure 5.0


1. Run BMT Service – This module runs the Biometric Management Tool.
2. Stop BMT Service – This module will stop the Biometric Management Tool.
3. Restart BMT Service – This module will restart the Biometric Management Tool.

VI. BMT Service is Running

  • If the steps in installing is done and you run the BMT Service, the system will indicate below that BMT Service is Running.
Runningbmt.JPG
Figure 6.0



REFERENCE

Media:Biometrics Installing.docx

Retrieved from "http://115.85.30.86:286/spgcwiki/index.php?title=BIOMETRICS_INSTALLING_AND_SETTINGS&oldid=6908"