View source for DATA COLLECTION ver 1.01

[[Main_Page | Main Page]] > [[Application_Development_Team | Application Development Team]] > [[System_Manual | System Manual]] > [[DATA_COLLECTOR |DATA COLLECTOR]]

[[File:555e1.jpg|300px|center]]

'''I. Collect Data'''

'''''Key Layout''''':

        Alphanumeric keypad is set to numeric mode by default. The [FN/ALPHA]
  as a toggle among in numeric, alpha (lower-case alphabetic), ALPHA (upper-case
  alphabetic) input modes.

      ''Note: It is not necessary to hold down the FN/Alpha key''.

        The associated icon will appear on the lower-right corner of the screen in a          sequence as shown below.
         '''Screen Icon              FN/ALPHA KEY                      Input Mode'''
           (none)                       N/A                          Numbers
              A             Press[FN/ALPHA] one time             Upper-case alphabetic
              a             Press[FN/ALPHA] two times            Lower-case alphabetic
              F             Press[FN/ALPHA] three times          Function mode
 


 
 '''Process''':
  1. After clicking the '''Power On''' button the device selection menu will
     display.

  2. Click '''Enter/OK''' button.

  3. Input the Store Name then click '''Enter/OK''' button.

  4. Next input the Sell/Stock area

  5. After inputting the Sell/Stock area click '''Enter/OK''' button.

  6. Then input the name of the Checker press '''Enter/OK''' button again.

  7. Press the '''Scan''' button to get the barcode of the item.

  8. Next input the number of quantity.

  9. Then click '''Enter/OK''' button.

  10. To scan another items repeat the steps from STEP 6 – STEP 8.

      ''Note: If you want to change the Store Name, Sell/Stock area and Checker click
  the Back/Cancel button once for you to return in STEP 3''.

'''II. Upload Data'''

     ''Note: Before you start the steps in uploading data, be sure that your device was          properly''connected to your Computer same as the figure shown below''''.
[[File:111a.jpg|500px|center]]

   '''''Process''''':

  1. Open '''Remote Console''' application installed in your computer.
[[File:222b.jpg|center|600px]]

     ''Note: If '''Remote Console''' window did not display after clicking the
  application. See the '''Toolbars''' then look for the icon of '''Remote Console'''
  
  Point the mouse in the icon.
  Next right click.
  Then select/choose '''Maximise'''''.

  2. Click '''System''' menu placed on the upper part of the '''Remote Console'''
    window.

  3. Next Click the '''Link Properties'''.

  4. In the '''Link Property Window''', click the dropdown button inline with
    label/word '''Interface'''.

  5. Next choose/select '''Cradle IR'''.

  6. Then beside '''Port''' input 9, to assign which data collector the user wants to
     access/connect.
   System Menu

  7. After assign the data collector, go back on the device (data collector)
   choose the '''Upload''' menu, by just simply clicking the drop down button
   then press '''Enter/OK''' button (after turning on the device). Wait until the
   device is totally connected.

  8. Next go back to the System ('''Remote Console''') click the '''Play/Start''' button
   placed on the left side upper part of the window. Wait until the Data
   Collector device will display a message that states “Sending Transf.:
   done”.

  9. Then data collector will ask which data user wants to delete, just choose
    one and then press '''Enter/OK''' button.

  10. A confirmation message will display then just choose if Yes/No and click
    '''Enter/OK''' button.

  11. Then click the Stop button placed beside the '''Play/Start''' button in
    '''Remote Console''' window.

  12. To view the uploaded file, go back to the '''Remote Console''' window.
  
  13. On the left side of the window click '''Files''' and the uploaded files will
display.

 '''III. File Format'''
[[File:333c.jpg|600px|center]]

  1. In the '''Remote Console''' window click '''System''' menu.

  2. Next select '''File Properties'''.

  3. File naming rules will display.
    System Menu
[[File:444.jpg|600px|center]]

  4. In rule number 6, beside '''File Name Format''' label input the
    number of rule you want to include in saving/uploading the
    file/data in the textbox provided.

  5. The series of the inputted rule numbers are the basis which rule
   number will comes first in uploading/saving the file.

  6. User can set the path where the file should be uploaded by
   simply clicking browse in the '''File Path''' layer.

  7. Next select the location and click '''OK'''.

  8. User can also set the extension name of the file by simply
    inputting the extension name in the textbox placed beside the
    label '''Data Filename Extension'''.

  9. Then click '''OK''' button.

 
 == '''Reference''' ==
   [[Media:DATA_COLLECTOR_USER'S_MANUAL.pdf|DATA COLLECTOR USER’S MANUAL Document]]


[[Main_Page | Main Page]] > [[Application_Development_Team | Application Development Team]] > [[System_Manual | System Manual]] > [[DATA_COLLECTOR |DATA COLLECTOR]]